Repeated Electrical Failures
Pumps, lights, electronics or accessories repeatedly stop operating even after individual components are replaced.
Complete Boat Rewiring
Rebuild the Electrical System From the Battery Forward.
GeauxPower Marine replaces deteriorated, overloaded and improperly installed boat wiring with an organized marine electrical system. Battery cables, buses, breakers, fuse blocks, switches, pumps, lighting, electronics and accessory circuits are designed to operate as one coordinated system.
When Rewiring Becomes Necessary
Electrical problems often indicate a larger system failure.
Replacing one failed switch or terminal may not solve a boat with deteriorated conductors, poor grounds, overloaded circuits or years of undocumented electrical modifications.
Corroded or Brittle Wiring
Conductors, terminals and connections show corrosion, heat damage, damaged insulation or loss of flexibility.
Unidentified Circuits
Wires have been added over time without labels, consistent routing or a clear connection to the correct fuse or switch.
Voltage Drop
Electronics reset, pumps slow down, lights dim or equipment behaves differently when other electrical loads are operating.
Improper Circuit Protection
Circuits contain oversized fuses, missing breakers, stacked connections or protection located too far from the power source.
Multiple Previous Repairs
The boat contains abandoned conductors, temporary splices, household wiring products or several generations of modifications.
Complete Rewire Scope
More than replacing wires behind the console.
A complete rewire begins with the battery system and follows the power path through primary protection, battery switching, distribution equipment and every connected load. The final scope depends on the boat, existing equipment and the systems being retained or upgraded.
View All Marine Services
Battery Cables
Starting, house and accessory conductors sized for current,
distance and equipment requirements.
Battery Switching
Battery switches, isolation, automatic charging relays and
emergency-combine arrangements.
Primary Protection
Main fuses and breakers positioned near the power source to
protect downstream conductors.
Positive and Negative Buses
Organized distribution points that eliminate unnecessary
stacked battery-terminal connections.
Fuse Blocks and Breakers
Protected branch circuits selected for the conductor and
connected equipment.
Switch Panels
Helm switches, relays and circuit controls wired into a
logical and serviceable layout.
Pumps and Lighting
Bilge pumps, livewell pumps, washdown systems, navigation
lighting and deck lighting.
Marine Electronics
Dedicated power, grounding and network support for
chartplotters, sonar and connected equipment.
Accessory Circuits
Horns, USB chargers, radios, amplifiers, Power-Poles and
additional onboard equipment.
Circuit Identification
Consistent labeling and routing that supports inspection,
troubleshooting and future additions.
Rewiring Process
A planned rebuild instead of another layer of repairs.
The system is evaluated before removal begins so retained equipment, required circuits, future additions and battery-system requirements can be incorporated into the new layout.
System Inspection
Review batteries, charging equipment, conductors, grounds, protection devices, switches and connected loads.
Electrical Layout
Define the battery configuration, distribution points, conductor routes, fuse blocks, breakers and circuit organization.
Removal and Installation
Remove abandoned or unsuitable wiring and install the new system with marine-grade conductors, terminals and protection.
Testing and Identification
Verify circuit operation, voltage supply, polarity, charging and equipment function before identifying the completed circuits.
Installation Standards
Designed for reliability and future service.
Marine-Grade Conductors
Tinned copper wiring selected according to circuit load, conductor length and allowable voltage drop.
Sealed Connections
Properly crimped terminals and adhesive-lined heat shrink used where environmental protection is required.
Logical Circuit Routing
Conductors supported and routed so they remain accessible without interfering with mechanical equipment or storage.
Dedicated Negative Distribution
Organized negative buses and return paths instead of scattered or unreliable grounding connections.
Correct Fuse and Breaker Sizing
Circuit protection selected to protect the conductors and satisfy the connected equipment requirements.
Clearly Identified Circuits
Circuit labels simplify future troubleshooting, equipment replacement and system expansion.
Request a complete boat-rewiring review.
Send the boat year, manufacturer and model, the electronics and accessories currently installed, the problems you are experiencing, and clear photos of the console, battery compartment and existing electrical system.